安徽省象形字数控机床有限公司是数控折弯机、数控剪板机等产品专业生产加工的公司，拥有完整、科学的质

量管理体系。安徽省象形字数控机床有限公司的诚信、实力和产品质量获得业界的认可。坐落在中国经济发展的

前沿—马鞍山 比邻 六朝古都 南京，占地面积6000平方米，现有员工200人，其中各级专精尖人才20多名。

公司专业设计、生产、销售电液伺服数控折弯机、数控液压闸式、摆式剪板机及普通型液压折弯机、液压剪板机

等板金加工设备，目前象形字已成为数控折弯机、剪板机生产基地之一。

性能特点：

 本机器采用钢板焊接结构,机身采用有限元分析设计、振动时效消除内应力，使机身稳定、可靠。

◎采用三点支撑滚动导轮，消除支撑间隙，提高剪切精度。

◎刀架剪切角能在一定的范围内调整，可使剪切材料变形量减小到理想状态，又可剪切超厚板料。

◎剪切行程任意调整，提高了工作效率，又可实现分段剪切功能。

◎后挡料设计了手动抬升功能，便于超长板料剪切。

◎墙板内侧设有手动加油泵，操作方便，保证关键部位的润滑。

◎插装式液压系统，减缓油温提升，增强机床运行的可靠性和安全性。

◎标配采用Delem专用系统，剪切计数、后挡料、剪切角及刀口间隙的调节直观、简单、方便。

◎可选用DAC310、DAC360数控系统以满足更高精度要求的剪切和控制。

Performance features:

This machine adopts the welded structure of the steel plate, and the fuselage is designed and vibration aging is eliminated and the

internal stress is eliminated, so the fuselage is stable and reliable..
Using the three point support rolling guide, eliminate the support gap, improve the cutting precision.
\ \ a shearing angle can be adjusted in a certain range, can reduce the shearing deformation, and shear super thick material.
The shearing stroke adjust, improve work efficiency, and can realize sectional shear function.
The rear stopper is designed for manual lifting function, long sheet metal shear.
The inner side of the wall with manual pumps, convenient operation, ensure the lubrication of the key parts.
The plug-in type hydraulic system, slow temperature increase, enhance the reliability and safety operation of machine.
\ \ a standard uses a special system of delem, counting shearing, the block material, shear angle and cutting edge gap

visual adjustment, simple and convenient.
You can choose DAC310, DAC360 CNC system to meet the control requirements of shear and high accuracy.

摆式剪板机维护保养的方法

1、严格按照操作规程进行操作。

2、每次开机前按润滑图表要求定时、定点、定量加润滑油，油应清洁无沉淀。

3、机床必须经常保持清洁，未油漆的部分应涂抹防锈油脂。

4、电动机轴承内的润滑漾油要定期更换加注，并经常检查电器部分工作是否正常安全可靠。

5、定期检查链条、手柄、旋钮、按键是否损坏，磨损严重的应及时更换，并报备件补充。

6、定期检查修理开关、保险、手柄、保证其工作可靠。

7、每天下班前10分钟，对机床加油润滑及擦洗清洁机床。

8、严禁非指定人员操作该设备，平常必须做到人离机停。

Shears maintenance method
1, strictly follow the operation procedures for operation.
2, every time before the start of the lubrication chart to require the timing, fixed point, quantitative lubricating oil, oil should be clean without precipitation.
3, machine tools must often keep clean, the part of the paint should be coated with rust preventive grease.
4, motor bearing lubrication overflow oil should be changed regularly filling, and always check whether the normal work of safe and reliable electrical parts.
5, regularly check the chain, handle, knob, key press whether damage, wear serious should be replaced, and to spare parts for spare.
6, check the repair switch, insurance, handle, guarantee its work reliably.
10, 7 minutes before work every day, lubrication and cleaning machine tool for machine tools.
8, non designated personnel to operate the device, usually must be done to stop the machine.